jhottell If you get a new keyless entry remote (key fob) or change the battery in your remote you may need to reprogram your vehicle to accept the remote. This procedure works for a lot of 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, and some 2008, and 2009 GM (Chevtolet and GMC) vehicles.
Read moreKeyless entry remote programming for 1998-2006 GM, Chevrolet, GMC
If you get a new remote or change the battery in your remote you may need to reprogram your vehicle to accept the keyless entry remote or key fob. This procedure works for a lot of 1998-2008 ford vehicles, see below for vehicles that the procedure works on and vehicles that use a slight variation on this procedure. I attempted to get this list accurate, I apologize because mistakes were probably made.
Read moreKeyless entry remote programming for Ford 1995-2008
Building my very first 3D printer was quite traumatic and time consuming but also fun and rewarding! I don’t suggest building your own unless you have a love for tinkering, and making. There are some other qualities that will come in handy such as tendency’s for hacking, electronics, and computers. As this is a computer controlled machine complete with a microcontroller you MUST know how to turn a computer on. Be aware that building your own RepRap is more like getting a hobby than getting a project.
Programming a button press with VB and your @Netduino, Event handlers and interrupt ports. In this tutorial I show how to program the Netduino to light up the onboard LED when the button is pressed, I then go into event handlers and latching buttons.
This is the first in a series of tutorials on programming the Netduino with Visual Basic or VB. You can program the netduino with either C# or VB but VB is now my language of choice.
Programming your Netduino with C# is fine and all, however, I am not going to do it any more. It is super easy to make the switch to a more forgiving programming language by the name of Visual Basic or VB.
In order to upgrade or replace the firmware in your Netduino you will need to download some software first.
I’ve seen videos on YouTube using an Arduino and a Graphical LCD screen (GLCD) to create a simple Oscilloscope. The annoying thing is that I found no help whatsoever on how to build one. I spent a few days figuring out how to use the Nokia 3310 LCD screen and then figuring out how to sample an analog port to create a fun oscilloscope effect.
Read moreDIY Arduino Oscilloscope with the Nokia 3310 GLCD screen
As a follow up to my DIY Arduino Oscilloscope video or as a stand alone tutorial, this video should help you understand arrays and recursion in Arduino. You can find the original post here: DIY Arduino Oscilloscope with the Nokia 3310 GLCD screen
I had a need for a temperature scanner to troubleshoot overheating on my Duramax LB7 pickup while towing. A commercial solution to collect 6 temperatures may have run me over a thousand dollars so I ordered some thermistors and for about 40 bucks in parts made one myself.
As it is getting cold again and my chickens made it through the summer just fine, it is time to revisit and revitalize my automatic chicken door.
The older model was a large door that slid on a track that would get leaves, snow, and ice messing the whole thing up. Also the mecanisim that opened the door was a string that tension was held on with springs, the string would knot up and stop working, blowing the fuse sometimes.
In this video I show how to connect a servo to a Netduino and also how to program the servo library into a new solution. The sweep program will drive the arm of the servo back and forth while the Knob program will move the arm of the servo when you turn a potentiometer.
In this video I show how to connect a servo to an Arduino and also how to load the sample servo programs included with the Arduino software. The sweep program will drive the arm of the servo back and forth while the Knob program will move the arm of the servo when you turn a potentiometer.
An attempt to make a good solar reflector out of mirror pieces and a Direct TV satellite dish. If I had it to do again I would have had an actual glass cutter and cut 1” squares…
Read moreBuilding a Parabolic Solar Reflector out of a Satellite Dish
Peltier Coolers or Thermal Electric Coolers are used to make things hot or cold but have another cool use. Apply a heat source to one side and keep the other side cool and the Peltier generates electricity.
Looking for the Add-In Manager in Microsoft Visual Studio 2010 Express? Trying to figure out how to install Add-ins? Sorry …
The Zune HD 32 is a nice MP3 and HD video player that can be compared to the IPod Touch. Zune HDs user interface is intuitive and snappy with some really cool features. If you dislike the IPod, ITunes, or Apple this is a really cool device however it doesn’t have the sheer number of apps as the previously mentioned competition.
The absolute beginners guide to programming an Arduino Duemilanove for the first time. I will take you through downloading the Arduino programming software, configuring the software, writing your first program, sending it to the Arduino, and testing operation.
The transistor is the fundamental building block of modern electronic devices, it is a semiconductor device used to amplify and switch electronic signals.
More simply a transistor is a valve for electricity. In this video I demonstrate the two types of transistors (NPN and PNP) and explain their uses.
A Breadboard is a must for the electronics experimenter type of person for experimenting activities. It is made up of rows of pins that you can simply press in components and wires and they will be held in by pressure.
